Difference between revisions of "Capillary Tubes"

From Ug11bm
Jump to navigationJump to search
Line 5: Line 5:
11-BM does '''not''' provide glass or quartz capillaries for mail-in experiments.  Only Kapton tubes (with an inner diameter of 0.81 mm) are provided for the mail-in service.
11-BM does '''not''' provide glass or quartz capillaries for mail-in experiments.  Only Kapton tubes (with an inner diameter of 0.81 mm) are provided for the mail-in service.


Users are referred to the following vendors in the USA for capillaries:
Users are referred to the following vendors in the USA for glass or quartz capillaries:


Charles-Supper
Charles-Supper
Line 15: Line 15:
http://hamptonresearch.com/menus.aspx?id=3&sid=110
http://hamptonresearch.com/menus.aspx?id=3&sid=110


Unless smaller sizes are required to avoid high [https://wiki-ext.aps.anl.gov/ug11bm/index.php/X-ray_absorption_%26_fluorescence X-ray absorption],


https://wiki-ext.aps.anl.gov/ug11bm/index.php/X-ray_absorption_%26_fluorescence
Tubes with diameter of 0.5 mm or 0.7 mm are recommended. These tubes are pre-sealed on one end, and have a flared opening on the other end for easy powder loading.


Due to small variations glass or quartz tube sizes, the 0.7 mm diameter size can be a tight fit in 0.8 mm Kapton tubes, but usually work.


 
Smaller tubes (e.g 0.3 mm) may be useful to lower [https://wiki-ext.aps.anl.gov/ug11bm/index.php/X-ray_absorption_%26_fluorescence X-ray absorption],  
 
the 0.5 mm (always) and the 0.7 mm (sometimes) diameter capillaries fit inside the standard Kapton tubes supplied by 11-BM for mail-in samples. The Kapton tubes have a ID of 0.81 mm.   The precision of the glass or quartz capillaries is sometimes poor, so the 0.7 can be tight fit, but usually work.


When returning samples loaded in glass capillaries, please leave a note in the package so we be sure to take extra care when handling.
When returning samples loaded in glass capillaries, please leave a note in the package so we be sure to take extra care when handling.


best regards
Matthew
Capillary Tubes available at 11-BM for on-site experiments





Revision as of 22:16, 16 September 2011

Mail-in Users

Specific mail-in samples (for example air sensitive material) may require the use of additional glass or fused quartz capillary tubes. Any additional capillary must fit and be secured inside the supplied Kapton tube.

11-BM does not provide glass or quartz capillaries for mail-in experiments. Only Kapton tubes (with an inner diameter of 0.81 mm) are provided for the mail-in service.

Users are referred to the following vendors in the USA for glass or quartz capillaries:

Charles-Supper http://www.charles-supper.com/en/page/category.cfm?idCategory=13

or

Hampton Research http://hamptonresearch.com/menus.aspx?id=3&sid=110


Tubes with diameter of 0.5 mm or 0.7 mm are recommended. These tubes are pre-sealed on one end, and have a flared opening on the other end for easy powder loading.

Due to small variations glass or quartz tube sizes, the 0.7 mm diameter size can be a tight fit in 0.8 mm Kapton tubes, but usually work.

Smaller tubes (e.g 0.3 mm) may be useful to lower X-ray absorption,

When returning samples loaded in glass capillaries, please leave a note in the package so we be sure to take extra care when handling.


On-Site Users

A section of Kapton, Glass and fused Quartz capillary tubes are available at 11-BM for on-site experiments. Check with staff to confirm, but the materials and dimensions shown below are typically on hand.

11BMCapillaryTubing.png

File:11BMCapillaryTubing Stock.pdf