Difference between revisions of "34ID-E Coordinate Systems"
From 34-ID-E
Jump to navigationJump to search| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{Incomplete}} | |||
== Beamline Coordinates == | == Beamline Coordinates == | ||
=== X-Y-Z === | === X-Y-Z === | ||
[[Image:Coordinates_beamline.png|right|thumb|400px|34IDE beamline XYZ and XHF coordinate systems, side view from outside of the ring.]] | |||
* X: radial direction of the ring, horizontal, pointing outboard to the doors. | * X: radial direction of the ring, horizontal, pointing outboard to the doors. | ||
* Y: vertically upward (against gravity). | * Y: vertically upward (against gravity). | ||
| Line 8: | Line 12: | ||
=== X-H-F === | === X-H-F === | ||
Because we routinely deal with motions in 45°-tilted directions, H and F are introduced as alternative coordinates to Y and Z: | Because we routinely deal with motions in 45°-tilted directions, H and F are introduced as alternative coordinates to Y and Z: | ||
* H: | * H: 45° upward-downstream (combination of +Y and +Z), this is the typical movement direction of the [[Differential Aperture|depth-profiling wire]]. | ||
* F: | * F: 45° downward-downstream (combination of -Y and +Z), this is the "focus" direction of the sample under the optical microscope. | ||
<math>H = \frac{1}{\sqrt{2}}(Y+Z)</math> | |||
<math>F = \frac{1}{\sqrt{2}}(-Y+Z) </math> | |||
<br clear=all> | |||
== Detector Coordinates == | == Detector Coordinates == | ||
[[Image:Coordinates_beamline+detectors_3d.png|thumb|330px|left|Figure A.]] | |||
[[Image:Coordinates_detectors.png|frame|right|Figure B.]] | |||
'''Figure A''' (left): A 3D cartoon showing detector image coordinates together with the beamline XYZ coordinate system. | |||
'''Figure B''' (right): 2D diagram showing the "bottom view" (viewed from the sample spot) of the three detectors. This view also correspond to the relative positions between the three detector's images as they are displayed on the beamline computer monitors. | |||
<br clear=all> | |||
== Coordinate Systems in Data Analysis == | == Coordinate Systems in Data Analysis == | ||
{{incomplete}} | |||
When analyzing or displaying data in [[LaueGo]], one need to know the definitions of coordinate systems in these occasions: | |||
====In 2D/3D plotting==== | |||
====In strain refinements==== | |||
Latest revision as of 21:36, 18 October 2013
| (This article/section is incomplete, please check back again or help expanding it) |
Beamline Coordinates
X-Y-Z
- X: radial direction of the ring, horizontal, pointing outboard to the doors.
- Y: vertically upward (against gravity).
- Z: along the x-ray beam
X-H-F
Because we routinely deal with motions in 45°-tilted directions, H and F are introduced as alternative coordinates to Y and Z:
- H: 45° upward-downstream (combination of +Y and +Z), this is the typical movement direction of the depth-profiling wire.
- F: 45° downward-downstream (combination of -Y and +Z), this is the "focus" direction of the sample under the optical microscope.
<math>H = \frac{1}{\sqrt{2}}(Y+Z)</math>
<math>F = \frac{1}{\sqrt{2}}(-Y+Z) </math>
Detector Coordinates
Figure B.
Figure A (left): A 3D cartoon showing detector image coordinates together with the beamline XYZ coordinate system.
Figure B (right): 2D diagram showing the "bottom view" (viewed from the sample spot) of the three detectors. This view also correspond to the relative positions between the three detector's images as they are displayed on the beamline computer monitors.
Coordinate Systems in Data Analysis
| (This article/section is incomplete, please check back again or help expanding it) |
When analyzing or displaying data in LaueGo, one need to know the definitions of coordinate systems in these occasions:
